How to Replace a Kia Sportage Replacement Key
The key of a lot of Kia models has a keyless entry system built in. g28carkeys.co.uk like an remote control, and is exchangeable by a Kia dealer.
Key fobs might stop working due to various reasons, such as batteries that are dead, worn buttons or buttons, signal interference, water damage, and a defective receiver module. Here are some tips to assist you in getting your Kia sportage replacement key to work again.
How to replace the remote key or smartkey?
The battery inside your Kia's smart key will eventually need to be replaced, regardless of whether it is a remote key that starts with a push button or a standard metal key that is not equipped with transponder. This is especially when your car displays a message that indicates the remote or smart keys are in poor condition.
Luckily, it's a relatively simple process. To replace the battery on the key fob take the mechanical key from the slit on the back of the key fob. Next, break the cover. A small screw is inside the key fob that holds the battery in its place. Take out the old battery by detaching the screw using a small screwdriver. Then insert the new one and close the slit inside the key fob.
When the key fob is equipped with an updated battery, test it by pressing the locks and unlock buttons. It's okay when the doors lock or unlock as expected. You can now use the Kia's hands-free lock/unlock feature when your fingers are cold or you have to run some errands in Brandon.
Note: Certain keys may require to be programmed (transponder chips or smart keys). This requires a special programming machine that only the dealer or automotive locksmith has access to. Other keys (non-transponder metal keys) don't require programming. If your keys need to be reprogrammed, you will need to be aware of the number printed on the key code tag and keep it in a secure location.
How do you replace the battery?
If your Kia key fob is not responding when you press the lock or unlock button on the fob, this is a signal that the battery should be replaced. A low battery may cause other issues, such as the check engine light turning on or the engine not cranking properly. Fortunately, replacing the battery on the key fob is a fairly simple DIY project that requires only some basic tools.
Before beginning the process be sure that your vehicle is turned off and that all doors are shut. Find the small, metal or plastic piece that is on the bottom of your key fob and gently jiggle it until the metal key slides out. You can then insert this key into the door handle of the driver to open your car.
To replace the battery inside the key fob, remove the cover on the rear. Use a plastic pry tool to loosen the latch that holds the black negative cable. Remove the old battery and then orient the new one so that the "+" positive side is facing you and the "negative" negative side is facing towards the fob's metal electrical contacts. Push the new CR2032 battery straight into place with care to avoid using too much force to avoid bending or damaging the metal contacts.
After you have installed the new battery and turning the key fob off and on in the ignition until the door locks up. You can then test the Kia's Key fob once more to ensure it's working as intended.
How to replace a smart key
You may have either the standard keyfob or Smart Key based on the model of Kia Sportage. The smart key has an embedded mechanical key blade while the standard key fob does not. Both kinds of key fobs contain batteries inside that will eventually need to be replaced. This is a simple procedure that takes only two minutes.
Be sure to switch off your Kia and stand on a level well-lit and well-lit area before you begin. Also, remember that there are tiny parts inside the fob which could fall out if not careful.
The small release button is located on the lower backside. It will be either a circular silver button or a rectangular slot. After pressing this button the mechanical key blade will come out and you will be able to open the key fob.
Once you have the key fob opened then you can remove the old battery and replace it. The new battery is a the CR-2032, and it can be bought from a local or online auto parts store. After installation with the battery, you should be able to lock, unlock and start your car with your key fob even if your engine isn't running!
How to replace a mechanical key
The Kia key fob is a great option that lets us lock and unlock our vehicle with the push of one button. But like any device it may have issues from time to time. There are ways to fix these problems and keep your key fobs running for an extended period of time.
A dead or drained battery is among the most frequently encountered issues. This can cause your device to stop working or work intermittently. If this is the case it is time to replace the battery a new one.
If this does not solve the issue, you can use an ordinary screwdriver with a flat head to push the fob's plastic casing open. Be cautious not to damage any internal components or scratch the plastic. After opening, carefully remove the battery that was removed and replace it with a brand new one.
Close and open the door with the mechanical key. (Every kia fob comes with an emergency mechanical key which will fit into the slot). Test the key fob to check that it's functioning correctly. If the fob isn't working, call a locksmith or dealer to solve the issue. Make sure they make you an emergency key that can work across all door and trunk cylinders to avoid future lockouts.